Burglar resistance door

Single-leaf burglar resistance steel door or flap

RC4 - expert report No. 22-5/15.125, PIV-Velbert
RC3 - expert report No. 22-4/15.125, PIV-Velbert
RC2 - expert report No. 45-47/22.126, PIV-Velbert
RC1 - expert report No. 45-47/22.126, PIV-Velbert

according to DIN EN 1627 - 1630

Combinable with additional performance characteristics:

U_D-value ≥ 1.3 W/(m²K) according to EN ISO 10077-1

up to R_W (C;C_tr) = 53 (-1;-5) dB

according to EN ISO 10140-1 / EN ISO 10140-2 / EN ISO 717

proof of acoustic performance for security doors
(measurement reports, test reports, expert opinions)

according to DIN EN 14351-1 labelled

up to class 4 according to EN 12207 (± 600 Pa)

up to class C5 according to EN 12210 (± 2.000 Pa)

up to class 8A according to EN 12208 (+ 450 Pa)

according to DIN EN 12211 (up to 5,000 Pa)

class 2 (d + e) according to EN 12219 (deflection)

according to DIN EN 14351-1
proven for doors in escape and rescue routes

flush-mounted design FLAT

according to DIN EN 50310, DIN VDE 0100-410 resp. DIN VDE 0100-540

up to IP44 according to DIN EN 60529
test report 44-1/26 PIV Velbert

Performance characteristics are combinable with further door types „System Schröders“:

EI₂90-S_a4 (Fire door System Schröders TSN-11 CE)
EI₂60-S_a4 (Fire door System Schröders TSN-3 CE)
EI₂30-S_a4 (fire door System Schröders TSN-1 CE)
EI₂120-S_a4 (Fire door System Schröders EIS-11 CE)

tested according to EN 1634-1

S₂₀₀ (smoke control door System Schröders RSN-1 CE)

tested according to EN 1634-3

RS (smoke control door System Schröders RSN-1)

nach DIN 18095

up to class FB6 (e.g. bullet resistance door FBN-1)

tested according to EN 1522/1523 beim Beschussamt Ulm

• optional with fixed skylight / top panel

leaf thickness 68 mm to 69 mm - smooth double-walled
plate thickness 1 mm to 1.5 mm

• thin rebate
  • optional thick rebate

• mineral wool filling (other fillings available on request)
  • optional full-face glued and pressed with cover plate,
    thus particularly smooth and even door leaf

securing pins

seal depending on performance characteristics

• elastic rubber seal

corner frame

• optional enclosing frame
• optional block frame

rebate protection by ESP safety profile (patent-protected)

depending on performance characteristics

• without seal
• lowerable floor seal
• stop seal
• sliding seal / grinding seal

• RC4: glazing according to DIN EN 356 min. P6B
• RC3: glazing according to DIN EN 356 min. P5A
• RC2: glazing according to DIN EN 356 min. P4A
• RC1: glazing according to DIN EN 356 min. P4A

glass dimensions and -form variable

minimum frieze width: 100 mm

• optional with intermediate glass inset bars
• optional with port-hole
• optional in top panel

glass inset bars with concealed screw connection (for rectangular glazing)

2/3-part KO door hinges
with patented easy-running bearings as Easy-running doors
or with ball-Bearing spacer rings

• optional door hinge with 3D adjustment

• RC4: protection fitting DIN 18257 ES3
• RC3: protection fitting DIN 18257 ES2
• RC2: protection fitting DIN 18257 ES1
• RC1: protection fitting DIN 18257 ES1

• optional combinable with any approved handle or replacement set according to EN 1906 bzw. EN 179
• optional combinable with panic handle or panic bar according to EN 1125
• optional combinable with enclosure according to EN 179

• optional panic locking according to EN 179 resp. EN 1125

door closer according to DIN EN 1154

• in masonry(thk ≥ 115 mm)
• in concrete(thk ≥ 100 mm)
• in aerated concrete(thk ≥ 150 mm)
• in mounting walls(thk ≥ 100 mm)
• in timber stud walls(thk ≥ 120 mm)
• in steel frames / steel containers
• in facing walls

• optional blunt installation in soffit
• optional installation on the wall plate

• additional security devices possible
  (magnetic contact, bolt contact, e-opener...)
• stainless steel design